FREE 2-DAY SHIPPING FOR ORDERS OF $50 OR MORE, AND FREE RETURN SHIPPING

CineMate® 130 home theater system

Sold from 2014 - 2015

NOT YOUR PRODUCT?
Help us provide the best support by confirming your product below
Select your product
Product image
SUPPORT OPTIONS FOR
Loading
SEARCH
Enter a search term in the field above.
Nothing found. Please enter a valid search (i.e., connection help, no audio from headphones, etc.).

Remote is intermittent or does not control your Bose product

If your Bose remote control does not work or only sometimes controls the functions of your Bose product, try the following:

Be sure the remote control sensor on your product is not in direct light.

If the remote sensor on your product is in a very bright area (i.e. in excessive sunlight or lighting, nearby a bright TV or laptop screen, etc.), the light interference could affect the ability of your product to detect the IR light commands from your remote control. If there is excessive light on your product, try reducing it.

Check that nothing is blocking the front of your product.

If the remote sensor on your product is fully or partially covered, it might not detect the commands from your remote control. If anything is blocking the display on the front of your system console, move it and check if the issue is resolved.

Be sure the system display is clean.

Debris, smudges or scratches on the plastic display cover can interfere with communication between the remote and the system. Use a clean, dry cloth to gently wipe the display.

Try new batteries in the remote.

In case the battery or batteries in your remote are low or have no power, replace them. Alkaline batteries are recommended over rechargeable batteries, which might output lower voltage. (Note: Battery testers are not always reliable since they might detect power but not indicate if there is adequate power for the remote.)

Be sure the remote is within range of the system.

The range of the remote is 20 feet

Check to see if any buttons on the remote are working.

If some buttons on the remote work and some do not work, see Certain remote control buttons do not work.

Reset your control console.

A reset is used to correct occasional product issues. It is not something that a product should require repeatedly. For more information, see Resetting your product.

Reset the universal remote.

Note: This process will erase all programming from the remote, including device codes and simultaneous system/device on/off control.
  1. On the remote control, press and hold a source button (i.e., TV or CBL-SAT) until all six source buttons glow, then release. The button that was held remains glowing
  2. On the number keypad, enter 981. The source buttons flash to confirm 
  3. Reprogram the remote. For more info, see Programming your remote.

Check for and install any available product updates.

See if the remote is sending IR signal by looking at the top edge of the remote through a camera viewfinder.

Our eyes cannot detect the IR (infrared) light produced by your remote but many digital cameras can. Look at the top edge of the remote through a digital camera (i.e. a smartphone camera), then press a button on the remote. If you do not see a flash through the camera viewfinder when a button is pressed, the remote is not sending any signal*. If you do see a flash but the remote is not working, try the other troubleshooting suggestions to help determine if the issue is the remote or something else.

*Some smartphones have IR filters on the front and/or rear cameras, which prevents them from seeing this flash. So, if you don't see a flash, try both the front and rear camera, a different camera if available, and any other troubleshooting suggestions.

The Control Console may need service.

If the steps provided do not resolve your issue, the Control Console may need service. Follow the link below for more information on how to service the Control Console. Depending on your product and region, you will be provided a contact number or the ability to setup service online.

Click here to start service

Your product may need service.

If the steps provided do not resolve your issue, your product may need service. Follow the link for more information on how to service your product. Depending on your product and region, you will be provided a contact number or the ability to setup service online.

Click here to start service
Loading
    Was this article helpful?
    Submit
    Thank you for your feedback!